UltraProflex SP- Rapid Strength Flexible Floor & Wall Tile Adhesive

Identification Of The Substance/Preparation and Company/Undertaking

Name of preparation:

PRODUCT NAME:	UltraProflex SP
APPLICATIONS:	Rapid Strength Flexible Floor & Wall Tile Adhesive
MANUFACTURER:	Instarmac Group plc Kingsbury Link Trinity Road Tamworth B78 2EX Tel. No.: 01827 872244 Emergency Tel. No: 07971 217 347

2 Composition/Information on Ingredients Chemical Description:

Consists of a mixture of cement powder, (Chromium VI present, less than .002%)
Ingredient EINECS ELINC CAS Classific Risks
ation Content
Silica Sand 238-878-4 - 14808-60-7 - 30-60% None
Portland Cement - - 65997-15-1 - 5-10% None
Fondu Cement - - 65997-16-2 - 10-30% None

3 Hazards Identification

Odour:	No information available
Appearance:	No information available
Eye contact:	Causes irritation, possible redness of affected areas.
Skin contact:	Prolonged exposure may cause abrasive irritation of the skin.
Inhalation:	Prolonged exposure to the respirable fraction of the silica contained in this product may cause silicosis.
Ingestion:	Low single dose oral toxicity, may cause gastro-intestinal disturbances.

4 First-Aid Measures

Skin:	Wash affected areas thoroughly with soap and water. If irritation persists seek medical advice.
Eye Contact:	Immediately wash out eyes with clean water for at least 15 minutes. Irrigate eyes thoroughly whilst lifting eyelids. Seek medical attention if irritation persists.
Ingestion:	Do not induce vomiting. Rinse mouth with water (do not swallow). Give 200-300mIs (half pint) of water to drink. Seek medical attention.
Inhalation:	Remove patient to the fresh air. If breathing is difficult, oxygen should be given by a trained person. Seek medical attention if ill effects occur.

Eye wash station or means of irrigation should be readily available.

5 Fire-Fighting Measures
Non-combustible solid. Not flammable. In case of fire use extinguishing media appropriate to surrounding conditions.. In case of fire, do not breathe fumes.

6 Accidental Release Measures

Clean-up actions:	Mix with wet sand. Do not dry sweep. Sweep or shovel-up spillages and remove to a safe place. Place in an appropriate container. Do not empty into drains (S29).
Special precautions:	Avoid the raising of dust.

7 Handling and Storage

Handling:	Due regard should be paid to the Manual Handling Operations regulations.. Do not allow dust to accumulate on surfaces and equipment. When using do not eat, drink or smoke (S20121). Avoid contact with skin and eyes (S24/25). Do not breathe dust (S22).
Storage:	Store in a dry place in temperature between 5°C - 25°C. Protect from frost. The product should be stored in unopened bags clear of the ground and away from excessive draughts.

8 Exposure controls/personal protection

Engineering controls:	Engineering controls should be provided which maintain airborne concentrations below the relevant guidelines.
Precautionary measures:	Ensure adequate ventilation.

Occupational exposure controls

Personal protection:

Wear goggles giving complete eye protection. Wear approved respirator if exposure likely to exceed MEL/OES. Wear PVC gloves.

Exposure limit values:

Silica sand:	MEL/LTEL silica, respirable crystalline 0.3mg/rn3. A chemical hazard alert notice (CHAN No 35) has been issued for this substance recommending that exposure to this substance be reduced to 0.1mg/rn3 (8 hour TWA) or below.
Portland cement:	Total inhalable dust 10mg/rn3. Respirable dust 4mg/rn3. (8 Hr LTEL).

9 Physical and chemical properties
General Information:

10 Stability and reactivity

Conditions to avoid:

Stable

11 Toxicological information

Toxicological:

Prolonged exposure to respirable crystalline silica may cause lung damage (silicosis). May cause redness and irritation.

12 Ecological information

Ecotoxicity:	Presents little or no hazard to the environment.
Environmental fate:	To the best of our knowledge, the properties of this material have not been fully evaluated.
Environmental hazard values:	To the best of our knowledge, the properties of this material have not been fully evaluated.

13 Disposal Considerations

Classification:	Approved solid waste disposal or landfill site.
Disposal considerations:	Disposal should be in accordance with local, state or national legislation.

14 Transport information:
Not classified as hazardous for transport.

15 Regulatory information:

Classification & labelling:	This safety data sheet does not constitute a workplace risk assessment.
Applicable Laws:	This safety data sheet is provided in compliance with the EC Directive 2001 /58/EC.
Risk Phrases:	No applicable
Safety Phrase:	Not applicable

16 Other Information

Training advise:

If any further information is required contact Instarmac Group plc

Recommended restrictions on use:
Should always be used in accordance with material data sheet.

Further information:
(written references and/or technical contact point); Contact Instarmac Group for further information.
Sources of key data Chemicals (Hazard Information and Packaging for Supply) Regulations 2002 The
used to compile Compilation of Safety Data Sheets (Third Edition) Control of Substances the data sheet: Hazardous to Health (Regulations) 1998 Manual Handling Operation Regulations 1992 Information collated from raw materials suppliers. EH4O/2002

Users of products supplied by Instarmac Group plc should take appropriate measures to ensure working practices are in accordance with the Control of Substances Hazardous to Health Regulations (COSHH).

All information is based on results gained from experience and tests and is believed to be accurate but is given without acceptance of liability for loss or damage attributable to reliance thereon as conditions of use lie outside our control. Users should always carry out sufficient tests to establish the suitability of any products for their intended applications. No statements shall be incorporated in any contract unless expressly agreed in writing nor construed as recommending the use of any product in conflict of any patent. All goods are supplied to Instarmac Group plc's general conditions of sale.

Material Safety Data Sheet UltraProflex SPW

Identification Of The Substance/Preparation and Company/Undertaking

Name of preparation: +

UltraProflex SPW (WHITE) - Floor & Wall Tile Adhesive

Floor levelling compound

Instarmac Group plc Kingsbury Link Trinity Road Tamworth B78 2EX Tel. No.: 01827 872244 Emergency Tel. No: 07971 217 347

2 Composition/Information on Ingredients Chemical Description:
Consists of a mixture of cement powder, (Chromium VI present, less than .002%)
Ingredient EINECS ELINC CAS Classific Content Risks
ation
Silica Sand 238-878-4 - 14808-60-7 60-100% None
Portland Cement - - 65997-15-1 1-5% None

3 Hazards Identification
Irritant

Odour:	No information available
Appearance:	No information available
Eyes contact:	Causes irritation, possible redness of affected areas.
Skin contact:	Prolonged exposure may cause abrasive irritation to the skin.
Inhalation:	Prolonged exposure to the respirable fraction of the silica contained in this product may cause silicosis.
Ingestion:	Low single dose oral toxicity, may cause gastro-intestinal disturbance.

4 First-Aid Measures

Skin:	Wash affected areas thoroughly with soap and water. If irritation persists seek medical advice.
Eye Contact:	Immediately wash out eyes with clean water for at least 15 minutes. Irrigate eyes thoroughly whilst lifting eyelids. Seek medical attention if irritation persists.
Ingestion:	Do not induce vomiting. Rinse mouth with water (do not swallow). Give 200-300mIs (half pint) of water to drink. Seek medical attention.
Inhalation:	Remove patient to the fresh air. If breathing is difficult, oxygen should be given by a trained person. Seek medical attention if ill effects occur.

Eye wash station or means of irrigation should be readily available.

5 Fire-Fighting Measures
Non-combustible solid. Not flammable. In case of fire use extinguishing media appropriate to surrounding conditions.. In case of fire, do not breathe fumes.

6 Accidental Release Measures

Clean-up actions:	Mix with wet sand. Do not dry sweep. Sweep or shovel-up spillages and remove to a safe place. Place in an appropriate container. Do not empty into drains (S29).
Special precautions:	Avoid the raising of dust.

7 Handling and Storage

Handling:	Due regard should be paid to the Manual Handling Operations regulations.. Do not allow dust to accumulate on surfaces and equipment. When using do not eat, drink or smoke (S20/21). Avoid contact with skin and eyes (S24125). Do not breathe dust (S22).
Storage:	Store in a dry place in temperature between 5°C - 25°C. Protect from frost. The product should be stored in unopened bags clear of the ground and away from excessive draughts.

8 Exposure controls/personal protection

Engineering controls:	Engineering controls should be provided which maintain airborne concentrations below the relevant guidelines.
Precautionary measures:	Ensure adequate ventilation.

Occupational exposure controls

Personal protection:

Wear goggles giving complete eye protection. Wear approved respirator if exposure likely to exceed MEL/OES. Wear PVC gloves.

Exposure limit values:

Silica sand:	MEL/LTEL silica, respirable crystalline 0.3mg/rn3. A chemical hazard alert notice (CHAN No 35) has been issued for this substance recommending that exposure to this substance be reduced to 0.1mg/rn3 (8 hour TWA) or below.
Portland cement:	Total inhalable dust 10mg/rn3. Respirable dust 4mg/rn3. (8 Hr LTEL).

9 Physical and chemical properties
General Information:

10 Stability and reactivity

Conditions to avoid:

Stable

11 Toxicological information

Toxicological:

Prolonged exposure to respirable crystalline silica may cause lung damage (silicosis). May cause redness and irritation.

12 Ecological information

Ecotoxicity:	Presents little or no hazard to the environment.
Environmental fate:	To the best of our knowledge, the properties of this material have not been fully evaluated.
Environmental hazard values:	To the best of our knowledge, the properties of this material have not been fully evaluated.

13 Disposal Considerations

Classification:	Approved solid waste disposal or landfill site.
Disposal considerations:	Disposal should be in accordance with local, state or national legislation.

14 Transport information:
Not classified as hazardous for transport.

15 Regulatory information:

Classification & labelling:	This safety data sheet does not constitute a workplace risk assessment.
Applicable Laws:	This safety data sheet is provided in compliance with the EC Directive 2001 /58/EC.
Risk Phrases:	No applicable
Safety Phrase:	Not applicable

16 Other Information

Training advise:

If any further information is required contact Instarmac Group plc

Recommended restrictions on use:
Should always be used in accordance with material data sheet.

Further information:
(written references and/or technical contact point); Contact Instarmac Group for further information.
Sources of key data Chemicals (Hazard Information and Packaging for Supply) Regulations 2002 The
used to compile Compilation of Safety Data Sheets (Third Edition) Control of Substances the data sheet: Hazardous to Health (Regulations) 1998 Manual Handling Operation Regulations 1992 Information collated from raw materials suppliers. EH4O/2002

Users of products supplied by Instarmac Group plc should take appropriate measures to ensure working practices are in accordance with the Control of Substances Hazardous to Health Regulations (COSHH).

All information is based on results gained from experience and tests and is believed to be accurate but is given without acceptance of liability for loss or damage attributable to reliance thereon as conditions of use lie outside our control. Users should always carry out sufficient tests to establish the suitability of any products for their intended applications. No statements shall be incorporated in any contract unless expressly agreed in writing nor construed as recommending the use of any product in conflict of any patent. All goods are supplied to Instarmac Group plc's general conditions of sale.